Logic Level Converter Bi-Directional

Logic Level Converter Bi-Directional
Click To Enlarge

4 Channel Logic Level Converter Bi-Directional

This device allows you to easily connect a 3.3V device to a 5V system. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter will also work with 2.8V and 1.8V devices.

What really separates this Logic level converter from SparkFun's previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side.

The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the 'HV' pin, low voltage (3.3V for example) to 'LV', and ground from the system to the 'GND' pin.

Bi-Directional Logic Level Converter Hookup Guide

Introduction

Do you have a 3.3V I2C or SPI sensor that might go up in smoke if connected to a 5V Arduino? Or a 5V device that needs a workaround to be compatible with your 3.3V Raspberry PiArduino Due or pcDuino?

To get over this obstacle you need a device that can shift 3.3V up to 5V or 5V down to 3.3V. This is called logic level shifting. Level shifting is a dilemma so common we designed a simple PCB assembly to make interfacing devices a little easier: the Bi-Directional Logic Level Converter.

Iso of Bi-Directional Logic Level Shifter

Though they’re share the same shape and size, this bi-directional logic level converter shouldn’t be confused with the more “uni-directional” version. This converter can pass data from high to low and/or low to high on all channels. It’s perfect for level-shifting between devices that are sharing a data wire, like I2C or a one-wire interface.

Covered In This Tutorial

In this tutorial we’ll take an in-depth look at the Bi-Directional Logic Level Converter. We’ll examine the schematic and board layout – explaining what each pin on the board does. At the end we’ll go over some hookup examples to show how you might hook the board up for various interfaces.

Suggested Reading

Board Overview

If you take a peak at the board’s schematic, you’d find that the bi-directional logic level converter (let’s shorten that to BD-LLC) is actually a very simple device. There is basically one level-shifting circuit on the board, which is repeated four times to create four level-shifting channels. The circuit uses a single N-channel MOSFET and a couple pull-up resistors to realize bi-directional level shifting.

MOSFET logic level shifting circuit

The bi-directional level-shifting circuit used on all four channels of the BD-LLC.

Through some semiconductor magic, this circuit can shift a low voltage signal to high and/or shift a high-voltage signal to a low voltage. A 0V signal on one end remains a 0V signal on the other. For a complete analysis of this circuit, check out this excellentPhilips Application Note AN97055.

The Pinout

There are 12 total pins on the BD-LLC – two parallel rows of six headers. One row contains all of the high voltage (e.g. 5V) inputs and outputs, the other row has all things low voltage (e.g. 3.3V).

Annotated BD-LLC

The pins are labeled on both the bottom and top sides of the board, and organized into groups. Let’s look closer at some of the pin groups:

Voltage Inputs

The pins labeled HVLV, and two GND’s provide high and low voltage references to the board. Supplying a steady, regulated voltage to both of these inputs is required.

The voltage supplied to the HV and GND inputs should be higher than that supplied to the LV side. For example, if you’re interfacing from 5V to 3.3V, the voltage on the HV pin should be 5V, and the voltage on LV sould be 3.3V.

Data Channels

There are four separate data channels on the BD-LLC, each capable of shifting data to and from high and low voltages. These pins are labeled HV1LV1HV2LV2HV3LV3HV4, and LV4. The number at the end of each label designates the channel of the pin, and the HV or LV prefix determines whether it’s on the high or low side of the channel.

A low-voltage signal sent in to LV1, for example, will be shifted up to the higher voltage and sent out HV1. Something sent in HV3will be shifted down and sent out of LV3. Use as many of these channels as your project requires. You don’t have to use every single one.

Keep in mind that these level shifters are purely digital. They can’t map an analog voltage from one max voltage to another.

Hookup Examples

Assembly

Before you can plug the converter into your system, you’ll need to solder something into it. There are a lot of options here. You could solder straight male headers in, and plug it right into a breadboard. Or perhaps you want to solder wires directly into it. Pick an assembly method that melds with how you intend to use the board.

BD-LLC soldered up

Once your BD-LLC is soldered up, it’s time to hook it up. Your hookup will probably vary depending on which communication interface you’re using. Below we’ll show how to hook the level converter for three of the most common communication protocols.

Using the BD-LLC for Serial

Although you won’t be taking advantage of the BD-LCC’s bi-directional abilities, it’s perfectly fine to use the board to shift serial communication. Serial usually requires two signal wires – RX (receive) and TX (transmit) – which both have a defined direction. These signals can be passed through any of the four channels on the BD-LLC.

Let’s say, for example, you want to hookup an Electric Imp Breakout Board (which has a 3.6V maximum input voltage) to anArduino Uno via their UARTs. Here’s one possible hook up:

Arduino to Electric Imp serial via BD-LLC

Make sure LV is powered at 3.3V, and HV is at 5V. Double-check that the channels match up, and a-shifting you will go! You’ve even got two extra channels to shift as you please.

Using the BD-LLC for SPI

The BD-LLC’s four channels are a perfect match for most SPI communications. SPI usually requires four wires: MOSI (master out, slave in), MISO (master in, slave out), SCLK (serial clock), and CS (chip select). These four wires can each be routed through a channel on the BD-LLC.

For example, if you wanted to connect an Arduino to an ADXL345 Breakout Board, which has an operating range of 2.0-3.6V, here’s how the BD-LLC could be spliced in:

SPI ADXL345 to Arduino via BD-LLC

Since each of the channels on the BD-LLC are bi-directional any of the four SPI lines can go through any of the BD-LLC’s four channels.

Using the BD-LLC for I2C

I2C is the communication standard where the BD-LLC really shines, because it requires that both data and clock signals – SDA and SCL – be bi-directional. Each of those lines can be passed through any of the BD-LLC’s level-shifting channels.

For this example, let’s keep using the ADXL345 breakout but instead swap over to the I2C interface. We can even add another I2C device…how about the L3G4200D Gyroscope Breakout. Since I2C is only a two-wire interface, we have room on the BD-LLC to fit in a couple of extra signals, like the interrupt outputs from each board

I2C ADXL345, L3G4200D to Arduino via BD-LLC

The two 3.3V I2C devices can both share the same level shifted SDA and SCL lines. Even more I2C device can be added, as long as they have unique addresses.

 images are CC BY-NC-SA 3.0

  * Marked fields are required.
Qty*
Price $2.95
Availability In-Stock
# Available 24